Cisco 路由配置语句汇总
路由器是工作在OSI参考模型第三层——网络层的数据包转发设备。路由器通过转发数据包来实现网络互连。虽然路由器可以支持多种协议(如TCP/IP、 IPX/SPX、AppleTalk等协议),但是在我国绝大多数路由器运行TCP/IP协议。路由器通常连接两个或多个由IP子网或点到点协议标识的逻辑端口,至少拥有1个 物理端口。
路由器根据收到数据包中的网络层地址以及路由器内部维护的路由表决定输出端口以及下一跳地址,并且重写链路层数据包头实现转发数据包。路由器通 过动态维护路由表来反映当前的网络拓扑,并通过与网络上其他路由器交换路由和链路信息来维护路由表。路由器设备厂商最有名的是Cisco公司,以下是Cisco路由器配置的常用命令汇总,希望对正在学习和应用思科路由器的你有帮助。
启动接口,分配IP地址:
router> router>enable router# router# configure terminal router(config)# router(config)# interface Type Port router(config-if)# no shutdown router(config-if)# ip address IP-Address Subnet-Mask router(config-if)# ^z
配置RIP路由协议:30秒更新一次
router(config)# router rip router(config-if)# network Network-Number router(config-if)# ^z
配置IGRP路由协议:90秒更新一次
router(config)# router igrp AS-Number router(config-if)# network Network-Number router(config-if)# ^z
配置Novell IPX路由协议:Novell RIP 60秒更新一次
router(config)# ipx routing [node address] router(config)# ipx maximum-paths Paths router(config)# interface Type Port router(config-if)# ipx network Network-Number [encapsulation encapsulation-type] [secondary] ; router(config-if)# ^z
配置DDR:
router(config)# dialer-list Group-Number protocol Protocol-Type permit[list ACL-Number] router(config)# interface bri 0 router(config-if)# dialer-group Group-Number router(config-if)# dialer map Protocol-Type Next-Hop-Address name Hostname Telphone-Number router(config-if)# ^z
配置ISDN:
router(config)# isdn swith-type Swith-Type <--配置ISDN交换机类型,中国使用basic-net3--> router(config-if)# ^z
配置Frame Relay:
router(config-if)# encapsulation frame-relay [cisco | ietf ] router(config-if)# frame-relay lmi-type [ansi | cisco | q933a ] router(config-if)# bandwidth kilobits router(config-if)# frame-relay invers-arp [ Protocol ] [dlci ] router(config-if)# ^z
配置标准ACL:
router(config)# access-list Access-List-Number [ permit | deny ] source [ source-mask ] router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z
配置扩展ACL:
router(config)# access-list Access-List-Number [ permit | deny ] [ Protocol | Protocol-Number ] source source-wildcard [ Source-Port ] destination destination-wildcard [ Destination-Port ] [ established ] router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z
配置命名ACL:
router(config)# ip access-list [ standard | extended ] ACL-Name router(config [ std- | ext- ] nacl)# [ permit | deny ] [ IP-Access-List-Test-Conditions ] router(config [ std- | ext- ] nacl)# no [ permit | deny ] [ IP-Access-List-Test-Conditions ] router(config [ std- | ext- ] nacl)# ^z router(config)# interface Type Port router(config-if)# ip access-group [ACL-Name | 1~199 ] [ in | out ] router(config-if)# ^z
配置DCE时钟:
router# show controllers Type Port router(confin-if)# clock rate 64000 router(config-if)# ^z
配置PPP协议:
router(config)# username Name password Set-Password-Here router(config)# interface Type Port router(config-if)# encapsulation ppp router(config-if)# ppp outhentication [ chap | chap pap | pap chap | pap ] router(config-if)# ppp pap sent-username Name password Password router(config-if)# ^z
PAP单向认证配置实例:
验证方:
router-server(config)# username Client password 12345 router-server(config)# interface serial 0 router-server(config-if)# encapsulation ppp router-server(config-if)# ppp authentication pap router-server(config-if)# ^z
被验证方:
router-client(config-if)# encapsulation ppp router-client(config-if)# ppp pap sent-username Client password 12345 router-client(config-if)# ^z
PAP双向认证配置实例:
路由器 A:
routerA(config)# username B password 12345 routerA(config)# interface serial 0 routerA(config-if)# encapsulation ppp routerA(config-if)# ppp authentication pap routerA(config-if)# ppp pap sent-username A password 54321 routerA(config-if)# ^z
路由器 B:
routerB(config)# username A password 54321 routerB(config)# interface serial 1 routerB(config-if)# encapsulation ppp routerB(config-if)# ppp authentication pap routerB(config-if)# ppp pap sent-username B password 12345 routerB(config-if)# ^z
CHAP单向认证配置实例:
验证方:
router-server(config)# username router-client password 12345 router-server(config)# interface serial 0 router-server(config-if)# encapsulation ppp router-server(config-if)# ppp authentication chap router-server(config-if)# ^z
被验证方:
router-client(config-if)# encapsulation ppp router-client(config-if)# ppp authentication chap router-client(config-if)# ppp chap hostname router-client router-client(config-if)# ppp chap password 12345 router-client(config-if)# ^z
CHAP双向认证配置实例:
路由器 A:
routerA(config)# username routerB password 12345 routerA(config)# interface serial 0 routerA(config-if)# encapsulation ppp routerA(config-if)# ppp authentication chap routerA(config-if)# ppp chap hostname routerA routerA(config-if)# ppp chap password 54321 routerA(config-if)# ^z
路由器 B:
routerB(config)# username routerA password 54321 routerB(config)# interface serial 1 routerB(config-if)# encapsulation ppp routerB(config-if)# ppp authentication chap routerB(config-if)# ppp chap hostname routerB routerB(config-if)# ppp chap password 12345 routerB(config-if)# ^z
Telnet使用:
routerA# terminal monitor routerA# telnet IP-Address [ Router-Name ] routerB# [ exit | logout ] routerB# ++再按 routerA# show sessions routerA# Connect-Number routerA# disconnect IP-Address [ Router-Name ] routerA# show user routerA# clear line [ 0 | 1 | 2 | 3 | 4 ]
禁止任何Telnet到本机:
router(config)# line vty 0 4 router(config-line)# access-class ACL-Number router(config)# ^z
设置主机名:
router(config)# hostname Set-Hostname router(config)# ^z router(config)# ^z
设置用户模式密码:
router(config)# line console 0 router(config-line)# login router(config-line)# password Set-Password router(config-line)# ^z
设置Telnet密码:
router(config)# line vty 0 4 router(config-line)# login router(config-line)# password Set-Password router(config-line)# ^z
设置特权模式密码:
router(config)# enable password Set-Password router(config)# enable secret Set-Password router(config)# ^z
给所有密码加密:
router(config)# service password-ancryption Set-Password-Here router(config)# no service password-ancryption router(config)# ^z
设置登录Banner:
router(config)# banner motd 分隔符 Set-Banner-InFORMation-Here 分隔符 N
设置接口的描述信息:
router(config-if)# description Set-Port-InFORMation-Here router(config)# ^z
CDP的控制:
router(config-if)# cdp enable router(config-if)# no cdp enable router(config)# cdp run router(config)# no cdp run
Ping的使用:
router# ping IP-Address router# ping Protocol [ip]:[ Protocol-Type ] Target IP address:IP-Address Repeat count [5]: Datagram size [100]: Timeout in seconds [2]: Extended commands [n]:y Sweep range of sizes [n]:
Tracke的使用:
router# trace IP-Address [ Host-Name ]
为Cisco 4000路由器指定媒体类型:
router(config-if)# media-type 10baset router(config-if)# ^z
更改路由器启动顺序:
router(config)# boot system flash IOS-FileName router(config)# boot system tftp IOS-FileName TFTP-IP-Address router(config)# boot system rom router(config)# ^z
修改寄存器数值:
router(config)# config-register value
在ROM监视器中更改寄存器数值:
> o/r value
路由器密码的恢复:
> o/r 0x2142 或 > confreg 0x2142 router> I router> n router> enable router# copy startup-config running-config router# configure terminal router(config)# enable secret New-Password router(config)# config-register 0x2102 router(config)# ^z router# copy running-config startup-config router# reload
冷关机,然后再开机并在60秒内按< Ctrl>+进入ROM监视器模式
配置名称-主机入口:
router(config)# ip host Set-Name [ TCP-Port-Number ] IP-Address [ IP-Address 2 ]... router(config)# ^z
定义DNS主机:
router(config)# ip name-server Server-Address [ Server-Address 2 ]... router(config)# ^z
禁用DNS:
router(config)# no ip domain-lookup router(config)# ^z
配置水平分割:
router(config-if)# ip split-horizon router(config-if)# no ip split-horizon router(config-if)# ^z
配置静态路由:
router(config)# ip route IP-Address Subnet-Mask [ Next-Hop-Address | Local-Out-Port ] [Distace ] router(config)# ^z
配置缺省路由:
router(config)# ip defoult-network IP-Address router(config)# ip route 0.0.0.0 0.0.0.0 [ Next-Hop-Address | Local-Out-Port ] [Distace ] router(config)# ^z
其它命令:
router# show version router# show running-config router# show startup-config router# show flash router# show interface [ Type Port ] router# show buffers router# show protocol router# show mem router# show stacks router# show processes router# show cdp entry [ Device-Name ] router# show cdp neighbors router# show cdp neighbors detail <---显示所有邻居三层信息-> router# show ip router router# show ipx router router# show host router# show ip protocol router# show ip interface Type Port router# show ipx interface Type Port router# show ipx servers router# show ipx traffic router# show access-lists [ ACL-Number ] router# show isdn status router# show dialer <--查看ISDN拨号信息--> router# show isdn active router# show frame-relay pvc router# show frame-relay map router# show frame-relay lmi router# erase startup-config router# reload router# setup router# copy running-config startup-config router# copy startup-config running-config router# copy tftp running-config router# copy running-config tftp router# debug ipx routing activity router# debug ipx sap router# debug isdn q921 router# debug isdn q931 router# debug dialer router# debug ip rip router# clear interface bri [ 0 | 1 | 2 ]