HCIP-BGP实验3

R1

[r1]int g0/0/0
[r1-GigabitEthernet0/0/0]ip add 12.1.1.1 24
[r1-GigabitEthernet0/0/0]int loopback0
[r1-LoopBack0]ip add 192.168.1.1 24
[r1-LoopBack0]int loopback1
[r1-LoopBack1]ip add 192.168.2.1 24
[r1-LoopBack1]int loopback3
[r1-LoopBack3]ip add 123.1.1.1 32

R2

[r2]int g0/0/0
[r2-GigabitEthernet0/0/0]ip add 12.1.1.2 24
[r2-GigabitEthernet0/0/0]int g0/0/1
[r2-GigabitEthernet0/0/1]ip add 23.1.1.2 24
[r2-GigabitEthernet0/0/1]int loopback0
[r2-LoopBack0]ip add 2.2.2.2 24
[r2-LoopBack0]int loopback1
[r2-LoopBack1]ip add 123.1.1.2 32

R3

[r3]int g0/0/0
[r3-GigabitEthernet0/0/0]ip add 23.1.1.1 24
[r3-GigabitEthernet0/0/0]int g0/0/1
[r3-GigabitEthernet0/0/1]ip add 34.1.1.1 24
[r3-GigabitEthernet0/0/1]int loopback0
[r3-LoopBack0]ip add 3.3.3.3 24
[r3-LoopBack0]int loopback1
[r3-LoopBack1]ip add 123.1.1.3 32

R4

[r4]int g0/0/0
[r4-GigabitEthernet0/0/0]ip add 34.1.1.2 24
[r4-GigabitEthernet0/0/0]int g0/0/1
[r4-GigabitEthernet0/0/1]ip add 45.1.1.2 24
[r4-GigabitEthernet0/0/1]int loop 0
[r4-LoopBack0]ip add 4.4.4.4 24
[r4-LoopBack0]int loop 1
[r4-LoopBack1]ip add 123.1.1.4 32

R5

[r5]int g0/0/0
[r5-GigabitEthernet0/0/0]ip add 45.1.1.1 24
[r5-GigabitEthernet0/0/0]int g0/0/1
[r5-GigabitEthernet0/0/1]ip add 56.1.1.1 24
[r5-GigabitEthernet0/0/1]int loop 0
[r5-LoopBack0]ip add 5.5.5.5 24
[r5-LoopBack0]int loop 1
[r5-LoopBack1]ip add 123.1.1.5 32

R6

[r6]int g0/0/0
[r6-GigabitEthernet0/0/0]ip add 56.1.1.2 24
[r6-GigabitEthernet0/0/0]int g0/0/1
[r6-GigabitEthernet0/0/1]ip add 67.1.1.2 24
[r6-GigabitEthernet0/0/1]int loop 0
[r6-LoopBack0]ip add 6.6.6.6 24
[r6-LoopBack0]int loop 1
[r6-LoopBack1]ip add 123.1.1.6 32

R7

[r7]int g0/0/0
[r7-GigabitEthernet0/0/0]ip add 67.1.1.1 24
[r7-GigabitEthernet0/0/0]int loopback0
[r7-LoopBack0]ip add 172.16.1.1 24
[r7-LoopBack0]int loop1
[r7-LoopBack1]ip add 172.16.2.1 24
[r7-LoopBack1]int loop2
[r7-LoopBack2]ip add 123.1.1.7 32

R8-R11根据地址继续往下配即可。

使AS内部通

R1

[r1]rip 1
[r1-rip-1]version 2
[r1-rip-1]network 123.0.0.0
[r1-rip-1]network 192.168.1.0
[r1-rip-1]network 192.168.2.0
[r1-rip-1]network 12.0.0.0

R2

[r2]rip 1
[r2-rip-1]version 2
[r2-rip-1]network 12.0.0.0
[r2-rip-1]network 2.0.0.0
[r2-rip-1]network 123.0.0.0

R3

[r3]ospf 1 router-id 3.3.3.3
[r3-ospf-1]area 0
[r3-ospf-1-area-0.0.0.0]network 34.1.1.1 0.0.0.0
[r3-ospf-1-area-0.0.0.0]network 3.3.3.3 0.0.0.0
[r3-ospf-1-area-0.0.0.0]network 123.1.1.3 0.0.0.0

R4

[r4]ospf 1 router-id 4.4.4.4
[r4-ospf-1]area 0
[r4-ospf-1-area-0.0.0.0]network 0.0.0.0 255.255.255.255

R5

[r5]ospf 1 router-id 5.5.5.5
[r5-ospf-1]area 0
[r5-ospf-1-area-0.0.0.0]network 45.1.1.1 0.0.0.0
[r5-ospf-1-area-0.0.0.0]network 5.5.5.5 0.0.0.0
[r5-ospf-1-area-0.0.0.0]network 123.1.1.5 0.0.0.0

R6

[r6]ospf 1 router-id 6.6.6.6
[r6-ospf-1]area 0
[r6-ospf-1-area-0.0.0.0]network 6.6.6.6 0.0.0.0
[r6-ospf-1-area-0.0.0.0]network 123.1.1.6 0.0.0.0
[r6-ospf-1-area-0.0.0.0]network 67.1.1.2 0.0.0.0

R7

[r7]ospf 1 router-id 7.7.7.7
[r7-ospf-1]area 0
[r7-ospf-1-area-0.0.0.0]network 0.0.0.0 255.255.255.255

R8-R11根据地址继续往下配即可。

建立BGP邻居

R1

[r1]bgp 100
[r1-bgp]router-id 1.1.1.1
[r1-bgp]peer 123.1.1.2 as-number 100
[r1-bgp]peer 123.1.1.2 connect-interface LoopBack 3

R2

[r2]bgp 100
[r2-bgp]router-id 2.2.2.2
[r2-bgp]peer 123.1.1.1 as-number 100
[r2-bgp]peer 123.1.1.1 connect-interface LoopBack 1[r2-bgp]peer 23.1.1.1 as-number 101

R3

[r3]bgp 101
[r3-bgp]peer 23.1.1.2 as-number 100[r3-bgp]peer 123.1.1.4 as-number 101
[r3-bgp]peer 123.1.1.4 connect-interface LoopBack 1[r3-bgp]peer 123.1.1.5 as-number 101
[r3-bgp]peer 123.1.1.5 connect-interface LoopBack 1

R4

[r4]bgp 101
[r4-bgp]peer 123.1.1.3 as-number 101
[r4-bgp]peer 123.1.1.3 connect-interface LoopBack 1[r4-bgp]peer 123.1.1.5 as-number 101
[r4-bgp]peer 123.1.1.5 connect-interface LoopBack 1

R5

（R5和R6使用环回接口建邻）
前提：R5和R6的环回可以相互ping通
所以先在R5和R6上写条静态路由

[r5]ip route-static 123.1.1.6 32 56.1.1.2
[r6]ip route-static 123.1.1.5 32 56.1.1.1

再使用环回建邻
注：由于EBGP之间的TTL默认为1，所以若使用环回建邻就必须修改TTL值

[r5]bgp 101
[r5-bgp]peer 123.1.1.3 as-number 101
[r5-bgp]peer 123.1.1.3 connect-interface LoopBack 1[r5-bgp]peer 123.1.1.4 as-number 101
[r5-bgp]peer 123.1.1.4 connect-interface LoopBack 1[r5-bgp]peer 123.1.1.6 as-number 102
[r5-bgp]peer 123.1.1.6 connect-interface LoopBack 1
[r5-bgp]peer 123.1.1.6 ebgp-max-hop 2

R6

[r6]bgp 102
[r6-bgp]peer 123.1.1.5 as-number 101
[r6-bgp]peer 123.1.1.5 connect-interface LoopBack 1
[r6-bgp]peer 123.1.1.5 ebgp-max-hop 2[r6-bgp]peer 123.1.1.7 as-number 102
[r6-bgp]peer 123.1.1.7 connect-interface LoopBack 1

R7

[r7]bgp 102
[r7-bgp]peer 123.1.1.6 as-number 102
[r7-bgp]peer 123.1.1.6 connect-interface LoopBack 2

R8-R11根据地址继续往下配即可。