一台计算机只能属于一个vlan,在思科模拟器上,怎么用一台路由器,一台交换机,和4台pc,要求划分两个VLAN是的pc可访问不同VLAN的PC...
对交换机的配置：
Switch
Switch
Switch
Switchen
Switch
Switchen
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Switch#vlan d
Switch#vlan database
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
Switch(vlan)#vlan 2 name a
VLAN 2 added:
Name: a
Switch(vlan)#vlan 3 name b
VLAN 3 added:
Name: b
Switch(vlan)#exit
APPLY completed.
Exiting....
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int vlan 2
%LINK-5-CHANGED: Interface Vlan2, changed state to upSwitch(config-if)#
Switch(config-if)#no shu
Switch(config-if)#int vlan 3
%LINK-5-CHANGED: Interface Vlan3, changed state to upSwitch(config-if)#
Switch(config-if)#no shu
Switch(config-if)#int f0/1
Switch(config-if)#sw m ac
Switch(config-if)#sw ac vlan 2
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to upSwitch(config-if)#
Switch(config-if)#int f0/2
Switch(config-if)#sw m ac
Switch(config-if)#sw ac vlan 3
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan3, changed state to upSwitch(config-if)#
Switch(config-if)#int f0/3
Switch(config-if)#sw m ac
Switch(config-if)#sw ac vlan 2
Switch(config-if)#int f0/4
Switch(config-if)#sw m ac
Switch(config-if)#sw ac vlan 3
Switch(config-if)#int f0/5
Switch(config-if)#no shu
Switch(config-if)#sw m ac
Switch(config-if)#sw m tr
Switch(config-if)#exit
Switch(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Switch#
对路由器的配置：
Press RETURN to get started!
Router
Router
Routeren
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#no shu
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#no ip ad
Router(config-if)#no ip address
Router(config-if)#int f0/0.1
%LINK-5-CHANGED: Interface FastEthernet0/0.1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.1, changed state to upRouter(config-subif)#
Router(config-subif)#en
Router(config-subif)#encapsulation d
Router(config-subif)#encapsulation dot1Q 2
Router(config-subif)#ip ad
Router(config-subif)#ip address 192.168.1.1 255.255.255.0
Router(config-subif)#int f0/0.2
%LINK-5-CHANGED: Interface FastEthernet0/0.2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.2, changed state to upRouter(config-subif)#
Router(config-subif)#en
Router(config-subif)#encapsulation d
Router(config-subif)#encapsulation dot1Q 3
Router(config-subif)#ip ad
Router(config-subif)#ip address 192.168.2.1 255.255.255.0
Router(config-subif)#exit
Router(config)#
我是在模拟器上做的，你可以看看这些命令，要是不明白的话再问吧。
取消
评论