当前位置：首页 > news >正文

用esp prog烧录ESP32-C3板踩坑

news 来源：原创 2024/7/5 4:23:21

附ESP32C3的GPIO一览：

esp32-c3-devkitm-1-v1-pinout

vscode选择Jtag烧录，终端输出esp_usb_jtag: could not find or open device：

D:\Devtools\Espressif\tools\openocd-esp32\v0.12.0-esp32-20230921\openocd-esp32\bin\openocd.exe -f board/esp32s3-builtin.cfgOpen On-Chip Debugger v0.12.0-esp32-20230921 (2023-09-21-13:40)
Licensed under GNU GPL v2
For bug reports, readhttp://openocd.org/doc/doxygen/bugs.html
Info : only one transport option; autoselecting 'jtag'
Info : esp_usb_jtag: VID set to 0x303a and PID to 0x1001
Info : esp_usb_jtag: capabilities descriptor set to 0x2000
Info : Listening on port 6666 for tcl connections
Info : Listening on port 4444 for telnet connections
Error: esp_usb_jtag: could not find or open device!

按照Configure ESP32-C3 Built-in JTAG Interface尝试解决，下了驱动：

Invoke-WebRequest 'https://dl.espressif.com/dl/idf-env/idf-env.exe' -OutFile .\idf-env.exe; .\idf-env.exe driver install --espressif

发现仍旧无法烧录，设备管理器一看没有相关的jtag unit驱动，只好尝试改用esp prog。

用esp prog烧录

参考了：https://blog.csdn.net/Marchtwentytwo/article/details/122071442

首先用espefuse查看芯片配置：

 espefuse.py -p COM7 summary

参考的文章是直接不指定串口执行的，我这边执行会报找不到串口的错误，原因是espefuse是通过串口来识别板子的，建议指定串口。

关于efuse设置可以参考esp官方c3的技术手册:https://www.espressif.com/sites/default/files/documentation/esp32-c3_technical_reference_manual_cn.pdf#iomuxgpio

我手上的这块c3版DIS_USB_SERIAL_JTAG已经被置位了，难怪装驱动时找不到JTAG unit.

espefuse.py v4.7.0
Connecting....
Detecting chip type... ESP32-C3=== Run "summary" command ===
EFUSE_NAME (Block) Description  = [Meaningful Value] [Readable/Writeable] (Hex Value)
----------------------------------------------------------------------------------------
Calibration fuses:
K_RTC_LDO (BLOCK1)                                 BLOCK1 K_RTC_LDO                                   = 4 R/W (0b0000001)
。。。Usb fuses:
DIS_USB_JTAG (BLOCK0)                              Set this bit to disable function of usb switch to  = False R/W (0b0)jtag in module of usb device
DIS_USB_SERIAL_JTAG (BLOCK0)                       USB-Serial-JTAG                                    = Enable R/W (0b0)
USB_EXCHG_PINS (BLOCK0)                            Set this bit to exchange USB D+ and D- pins        = False R/W (0b0)
DIS_USB_SERIAL_JTAG_ROM_PRINT (BLOCK0)             USB printing                                       = Enable R/W (0b0)
DIS_USB_SERIAL_JTAG_DOWNLOAD_MODE (BLOCK0)         Disable UART download mode through USB-Serial-JTAG = False R/W (0b0)Vdd fuses:
VDD_SPI_AS_GPIO (BLOCK0)                           Set this bit to vdd spi pin function as gpio       = False R/W (0b0)Wdt fuses:
WDT_DELAY_SEL (BLOCK0)                             RTC watchdog timeout threshold; in unit of slow cl = 40000 R/W (0b00)ock cycle

esp prog烧录参考下文:

由于 ESP32-C3 默认选用内置的 USB_SERIAL_JTAG 外设。此时需要烧录 efuse 来选择外接 JTAG 适配器，有以下两种方式：

烧毁 DIS_USB_JTAG eFuse：将永久禁用 USB_SERIAL_JTAG 和 CPU 的 JTAG 端口之间的连接。然后可以将 JTAG 接口连接到 GPIO4 - GPIO7。请注意，USB_SERIAL_JTAG 的 USB CDC 功能仍然可用，即仍然可以通过 USB CDC 进行烧录和 log 查看。

烧毁 JTAG_SEL_ENABLE eFuse：将启用由 Strapping 引脚 GPIO10 选择的 JTAG 接口。如果 ESP32-C3 复位时 Strapping 引脚为低电平，则 JTAG 接口将使用 GPIO4 - GPIO7。如果 Strapping 引脚为高电平，则 USB_SERIAL_JTAG 将用作 JTAG 接口。

我这边summary没有看到JTAG_SEL_ENABLE 选项，看来只能用DIS_USB_JTAG 方法了。

python -m espefuse -p COM7 burn_efuse DIS_USB_JTAGespefuse.py v4.7.0
Connecting....
Detecting chip type... ESP32-C3=== Run "burn_efuse" command ===
The efuses to burn:from BLOCK0- DIS_USB_JTAGBurning efuses:- 'DIS_USB_JTAG' (Set this bit to disable function of usb switch to jtag in module of usb device) 0b0 -> 0b1Check all blocks for burn...
idx, BLOCK_NAME,          Conclusion
[00] BLOCK0               is not empty(written ): 0x000000008000000000000000000000000000000000000000(to write): 0x000000000000000000000000000000000000020000000000(coding scheme = NONE)
.
This is an irreversible operation!
Type 'BURN' (all capitals) to continue.
BURN
BURN BLOCK0  - OK (all write block bits are set)
Reading updated efuses...
Checking efuses...
Successful

烧录完成后将esp prog连接至esp32c3对应引脚，用vscode的esp-idf扩展打开blink例子，测试烧录：

idf.py build 
或者
vscode ctrl+e然后b

若出现LIBUSB_ERROR_NOT_xxx错误，记得用Zadig将esp prog的对应interface0驱动更新：

jtag-usb-configuration-zadig

经测试，烧录成功！

然后F5, 测试gdb调试功能，毕竟花费这么久时间和心思用JTAG，不就是为了用gdb吗？

首先写好launch.json

{"version": "0.2.0","configurations": [{"name": "GDB","type": "cppdbg","request": "launch","MIMode": "gdb","miDebuggerPath": "${command:espIdf.getXtensaGdb}","program": "${workspaceFolder}/build/${command:espIdf.getProjectName}.elf","windows": {"program": "${workspaceFolder}\\build\\${command:espIdf.getProjectName}.elf"},"cwd": "${workspaceFolder}","environment": [{ "name": "PATH", "value": "${config:idf.customExtraPaths}" }],"setupCommands": [{ "text": "target remote :3333" },{ "text": "set remote hardware-watchpoint-limit 2"},{ "text": "mon reset halt" },{ "text": "thb app_main" },{ "text": "flushregs" }],"externalConsole": false,"logging": {"engineLogging": true}}]}